CWE-787
The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
CVE-2026-19576
CVSS 6.8/10 · ORTA · 11.10.2026
CWE: CWE-787
Vector: CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
🎯 AÇIK NEDİR?
Buffer Overflow / Memory Corruption
Açıklama: The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default o…
⚡ SALDIRI ZİNCİRİ
Saldırı adımları:
1. Fuzzing ile çöküş noktası tespit edilir: Boofuzz, AFL++ ile.
2. GDB/PEDA ile offset hesaplanır: pattern create 500 → crash → pattern offset EIP_VALUE
3. Stack/Heap layout analizi.
4. ROP gadget ile NX bypass.
5. Metasploit varsa: use exploit/... ; run
🔧 Araçlar: GDB+PEDA/pwndbg, ROPgadget, pwntools, Metasploit, AFL++
🗺️ MITRE ATT&CK: T1203 (Exploitation for Client Execution), T1068
🌍 GERÇEK DÜNYA ETKİSİ
Tüm gizli veriler okunabilir/çalınabilir; sistem verileri değiştirilebilir/silinebilir; hizmet tamamen devre dışı bırakılabilir.
🛡️ ÇÖZÜM VE MİTİGASYON
→ Üretici tarafından yayınlanan yamayı uygula.
→ ASLR/NX/Stack Canary aktif olduğunu kontrol et.
→ WAF kuralı ekle, anormal trafik için IDS alert oluştur.
⚠️ ACİLİYET
📋 Rutin güncelleme (30 gün)
────────────────────────────────────────
[Kural Tabanlı Analiz] [💡 config.json dosyasına ai_key (Claude: sk-ant-... veya Groq: gsk_...) ekleyerek gerçek AI analizi kullanabilirsiniz]
[⚠️ AI key mevcut ancak istek başarısız — kural tabanlı analiz kullanıldı]